Published at Thursday, July 13th 2017. by Nanine in Flooring.
Many people also have questions about the tiles durability and use. Interlocking floor tiles are usually placed on the floor underneath it, meaning there is no adhesive or floor base. Some may become concerned that the interlocking tiles will become loose easily due to the lack of adhesive. This is not the case. Tile floor systems are designed to lock together permanently. When appropriately installed, the interlocking floor tile should remain exactly as it was placed until the user decides to move it. Interlocking tile floors are appropriate for any use, from industrial to residential. This interlocking flooring system does not have as much risks compared to traditional tile flooring.
Carpet is probably the most common floor covering that is used in residential homes. It comes in a wide variety of colors and textures. Carpet consists of woven fibers, which protrude upwards, glued or woven into a foam or jute backing. Often an underpad of pressed foam is installed below it or the backing can be integral with the carpet, adding to the softness and providing a much more comfortable surface for walking on. Carpet is installed by either gluing the carpet to the sub-floor, or the use of carpet tack around the perimeter. A good carpet will has a close weave, which will not show the backing material when separated. To reduce project costs, some contractors will opt to install a high quality underlay, with a low or medium quality carpet. This provides the soft surface, with equal durability, giving the homeowner the benefits of high quality carpet, at a reduced cost.
Traditional tile installation requires many tools and lots of patience which have to be pre-set on the floor, cut down to size, then adhered to the floor using a strong industrial glue. They will not stick to every surface and frequently, a layer of floor base must be installed before the tiling work can begin. If the tiles are placed too close together, they can buckle, leaving unsightly bumps and lumps on the floor. If they are placed too far apart, there will be obvious gaps. If a mistake is made when laying down the tile, it is very difficult to fix as the tile is glued to the floor. The tile will have to be pried up, excess adhesive scraped, and the process started over. Laying traditional tile floors is a project that can take several days, to several weeks, to finish.
Ceramic tile is probably the most durable types of flooring and is typically installed in entry areas, where sand scuffing and water accumulations are the norm. Bathrooms and kitchens often get this type of floor treatment as well, but due to the high cost of installation, homeowners tend to not include these areas. Ceramic tile are typically a square tile, although interlocking units are on the market, in standard square measurements of 4", 6",8" or 12". They are installed by one of two primary methods, either set into a thin mortar bed (called "thinset adhesive"), which also acts like glue, or a heavyset bed of 1-1/2" normal mortar base. For all ceramic tile installations, the floor must be built up to ensure the strength required to prevent tile or joint cracking. Often, installers put down a material called "cement board", which is much like drywall, but is made of glass fibers and cement. In any case, ensure that your installer will offer you a guarantee against future cracking or uplift of tiles. Ceramic tiles require little maintenance, but beware, water on glossy floor tiles can be very slippery, and many a time, a homeowner has resented the installation of a high gloss tile, over a bathroom floor area.
Laying the floor is also another area that is worth thinking about when comparing the two types of oak flooring. The majority of engineered wood floors are longer and wider than most solid oak boards because this is the look that most people are wanting nowadays. The flooring being longer and wider means the flooring is quicker to fit. Another aspect that makes this floor easier and quicker to fit is how well machined the boards are. From our experience in the flooring industry we have had nothing but good feedback regarding how easy our engineered flooring was to lay, and this is down to how well machined the boards are. Given that engineered flooring is quicker and easier to fit, any extra money that is spent on purchasing an engineered oak floor is often compensated in the time that is saved fitting it! This is something to keep in mind when comparing prices.
This shrinking action pulls the floor together, adding strength to the overall system. The advantages of this type of sub-floor are its strength and durability. One important note, homeowners are often disturbed by the small 1/4" wide gaps, generally left between the individual planks after the wood dries out. Although disturbing to see during construction, upon completion, the spaces are not noticeable, and really have no impact on the sub-floor components at all. Strip floors are designed to be interlocking, through lapping or spacing of joints.