Published at Thursday, July 13th 2017. by Solaina in Flooring.
Most popularly used in bathrooms, kitchens, laundry areas and entryways are vinyl sheet, or linoleum floorings. This type of flooring cones in a vast array of colors, textures and patterns, in sheet sizes of 12 foot widths with varying lengths, and made from a vinyl composite, covered with a surface coating. It is installed by applying covering over the sub-floor, usually mahogany or particle core sheets 4`x4` in size, to which the vinyl is glued to. It can also be installed directly onto concrete floors, in areas such as basements. Joining two sheets together is a standard practice when the room width exceeds 12`, or under doorways. Sheet vinyl is a good flooring in areas where water tends to accumulate, like around bathroom fixtures or at entry ways. It is fairly durable, and often maintenance free. Linoleum is one of the cheapest types of flooring to install.
Another way to prevent undue and excessive wear on your hardwood floors or wooden floors is to use scatter or throw rugs in high traffic areas. You may even be tempted to use a center rug piece for decor. Now that you and I have gotten past the fun stair rail slide and onto the floor, it is utterly important that we stay clear of injury -- Ensure that your throw, scatter or centerpiece rug either has sufficient non-skid backing or that you lay a non-slip material between it and your wood floor.
Dust, grit and moisture are gifts of nature and we all have to deal with them. Grit which stems from sand or dirt being tracked from the outdoors on the surface works like sandpaper on the floor finish. Dust mites, balls and the like are merely pulverized bits of dirt which in essence acts in the same way as grit over the long haul on your floors. Once your floor finish gets damaged grit and dust left on the surface tend to discolor the hardwood while being ground into the surface pores with each step made on top of it like a hammer pounding stroke after stroke.
Did you see a picture that you like and now you have the bug that you want that special floor? The good news is that it could probably be made for you, but before you go a long ways down the path of choosing which floor you want and requesting a display room full of samples, ask about some price ranges. There is a common misconception that since reclaimed wood is supposedly salvaged it should be cheaper than virgin wood floors. If you are buying a quality kiln dried and precision milled product, generally that is not the case. The only cost savings would be if you found some scraps or did some salvage work yourself, you might save some costs. For example you might find a gym floor or planks out of a barn hay loft that you want to nail down on your floor. The material might have been next to free, but how much time are you going to have in making it usable and pulling nails? Are the results what you want?
There are three main types of sub-flooring installed to cover and span the floor structure. It is over this that the finished floor will be placed. The sub-flooring types include raw sheathing, interlocking and strip. It is utilized not only to provide a surface for the interior finishes to be placed on, but also to prevent twisting or torque forces placed on the building. The sub-floor also allows load sharing within the joist framing system. Often the sub-flooring is glued to the joist work to eliminate creaking floors and to prevent the floor joists from turning.
Are you going to be able to enforce the warranty? Also, do you really think that a finish can last a lifetime? For example take a nail and try scraping it across the surface. Sure it is a durable, well applied finish, but it is impossible to make a product that won`t get abused at some point in its lifetime. Do you think that the only serious trial your floor will ever see is a stinky sock? Read the fine print on the warranty and regardless of what it says consider the true replacement cost on the floor. It probably only covers the cost of material of the specific damaged product under normal wear and tear. Your product may not be made exactly the same later (trends and product lines change) to replace the section that is warrantied, so you may have to replace the whole floor years later. You will have labor cost along with displacement of trim, cabinets, and appliances. Also most of these lifetime finishes cannot be repaired or sanded because of a micro bevel put on the edge of prefinished floor. Our advice is instead to buy a quality product that can be refinished and repaired because something will go wrong in the lifetime of the floor; don`t get a false sense of security.