Published at Friday, July 28th 2017. by Nynette in Flooring.
Undoubtedly you`ve seen wood floors where it seems that the edges or seams of boards joined together curl up or the width of a board creates a bow like upward arc in the middle. These are indications of moisture damage to a wooden floor. For example, there have even been instances where moisture damage caused floor boards to arc together to raise a full length sofa about three feet into the air. That was merely from the curl effect and strength of water on wooden floor boards. So, by all means do dry any spills to keep moisture and liquids away from your wooden floors.
We personally do not care for prefinished flooring due to installation problems associated with it, so our product requires site applied finish. This means that your floor finish if site applied will be easier to sand and refinish than a prefinished floor. Also you do not have to deal with that micro bevel groove between each board that tends to fill up with dust and crumbs. Most prefinished hardwood floors really can`t be refinished easily. To sand it off means that the wear layer has to be thicker than the height of the nails and have room to sand off the micro bevel between boards; that amounts to a lot of sanding. You also will not be able to spot sand or touch up parts of the floor.
Traditional tile installation requires many tools and lots of patience which have to be pre-set on the floor, cut down to size, then adhered to the floor using a strong industrial glue. They will not stick to every surface and frequently, a layer of floor base must be installed before the tiling work can begin. If the tiles are placed too close together, they can buckle, leaving unsightly bumps and lumps on the floor. If they are placed too far apart, there will be obvious gaps. If a mistake is made when laying down the tile, it is very difficult to fix as the tile is glued to the floor. The tile will have to be pried up, excess adhesive scraped, and the process started over. Laying traditional tile floors is a project that can take several days, to several weeks, to finish.
As a reoccurring theme in this article you will find that you often get what you pay for. Admittedly, the higher end price point products ($11+/sf) from more rare woods are not necessarily better quality but we find that up to that point quality improves with price. Our solid wood floors range in price from $4-9 per square foot and our engineered ranges from $7-15 per square foot. We will discuss applications below, but our point is that you need to have a realistic budget when shopping. Sometimes a nice alternative if you have your heart set on an expensive floor is to use less of it and put it just in key areas. Don`t do the whole house. Maybe just do the main high traffic areas and use a cheaper alternative in bedrooms.
For the second variable here is a controversial opinion: we do not end match our flooring which means there is no tongue and groove on the ends of the planks. Since we recommend our floor be glued down we say this is an unnecessary expense for the customer. End matching reduces the yield in production and raises labor costs. Most end match profiles are milled so loosely that they really don`t hold the floor in place anyway. The biggest benefit to the installer is that the plank can be cut in half in any place and reused anywhere without have to mate up to a complementary tongue or groove since the end is just square cut. This means all end trim pieces or any waste can be reused. Therefore on our engineered flooring product the waste factor is virtually nothing unless there are angles or radiuses to work around. We also help with waste factor by usually supplying a random width product so when one gets close to the end of a room they can plan the width combination patterns out to not have to rip much off the last row.
Did you see a picture that you like and now you have the bug that you want that special floor? The good news is that it could probably be made for you, but before you go a long ways down the path of choosing which floor you want and requesting a display room full of samples, ask about some price ranges. There is a common misconception that since reclaimed wood is supposedly salvaged it should be cheaper than virgin wood floors. If you are buying a quality kiln dried and precision milled product, generally that is not the case. The only cost savings would be if you found some scraps or did some salvage work yourself, you might save some costs. For example you might find a gym floor or planks out of a barn hay loft that you want to nail down on your floor. The material might have been next to free, but how much time are you going to have in making it usable and pulling nails? Are the results what you want?