Published at Thursday, July 20th 2017. by Nynette in Flooring.
Many people also have questions about the tiles durability and use. Interlocking floor tiles are usually placed on the floor underneath it, meaning there is no adhesive or floor base. Some may become concerned that the interlocking tiles will become loose easily due to the lack of adhesive. This is not the case. Tile floor systems are designed to lock together permanently. When appropriately installed, the interlocking floor tile should remain exactly as it was placed until the user decides to move it. Interlocking tile floors are appropriate for any use, from industrial to residential. This interlocking flooring system does not have as much risks compared to traditional tile flooring.
Ceramic tile is probably the most durable types of flooring and is typically installed in entry areas, where sand scuffing and water accumulations are the norm. Bathrooms and kitchens often get this type of floor treatment as well, but due to the high cost of installation, homeowners tend to not include these areas. Ceramic tile are typically a square tile, although interlocking units are on the market, in standard square measurements of 4", 6",8" or 12". They are installed by one of two primary methods, either set into a thin mortar bed (called "thinset adhesive"), which also acts like glue, or a heavyset bed of 1-1/2" normal mortar base. For all ceramic tile installations, the floor must be built up to ensure the strength required to prevent tile or joint cracking. Often, installers put down a material called "cement board", which is much like drywall, but is made of glass fibers and cement. In any case, ensure that your installer will offer you a guarantee against future cracking or uplift of tiles. Ceramic tiles require little maintenance, but beware, water on glossy floor tiles can be very slippery, and many a time, a homeowner has resented the installation of a high gloss tile, over a bathroom floor area.
For the second variable here is a controversial opinion: we do not end match our flooring which means there is no tongue and groove on the ends of the planks. Since we recommend our floor be glued down we say this is an unnecessary expense for the customer. End matching reduces the yield in production and raises labor costs. Most end match profiles are milled so loosely that they really don`t hold the floor in place anyway. The biggest benefit to the installer is that the plank can be cut in half in any place and reused anywhere without have to mate up to a complementary tongue or groove since the end is just square cut. This means all end trim pieces or any waste can be reused. Therefore on our engineered flooring product the waste factor is virtually nothing unless there are angles or radiuses to work around. We also help with waste factor by usually supplying a random width product so when one gets close to the end of a room they can plan the width combination patterns out to not have to rip much off the last row.
Are you going to be able to enforce the warranty? Also, do you really think that a finish can last a lifetime? For example take a nail and try scraping it across the surface. Sure it is a durable, well applied finish, but it is impossible to make a product that won`t get abused at some point in its lifetime. Do you think that the only serious trial your floor will ever see is a stinky sock? Read the fine print on the warranty and regardless of what it says consider the true replacement cost on the floor. It probably only covers the cost of material of the specific damaged product under normal wear and tear. Your product may not be made exactly the same later (trends and product lines change) to replace the section that is warrantied, so you may have to replace the whole floor years later. You will have labor cost along with displacement of trim, cabinets, and appliances. Also most of these lifetime finishes cannot be repaired or sanded because of a micro bevel put on the edge of prefinished floor. Our advice is instead to buy a quality product that can be refinished and repaired because something will go wrong in the lifetime of the floor; don`t get a false sense of security.
Seventh, are you a do-it-yourselfer? Think through every step of the process to be sure that you can do it yourself. Usually the install can be done with relatively moderate skills and simple tools like a chop saw and rented flooring nailer. The finishing process is a whole different matter. The sanders and buffers take some special skills to operate. A normal price range for labor and materials to install a wood floor is $4-5 per square foot. It is possible to build your own sweat equity into a floor install. Maybe this is where you choose to use our engineered product for example because it is presanded to more accurate tolerances than a solid wood product. It can be touched up with a hand held orbital sander rather than industrial floor sanders. Then if you are doing the finish yourself, you will want to consider using a finish that may not require as much buffing between coats.
Most commonly installed are interlocking sheathing panels. This type of sheathing is generally 5/8" thick, and manufactured as either plywood or aspenite (commonly referred to as "chipboard") in 4` x 8` sheets. The sheets come with the long edges designed to interlock with a tongue on one edge, and a grove on the opposing edge. They are installed by simply pushing or pounding the sheets together, and nailing or screwing them to the joist work, in the same manner as raw sheathing. It is often the cheapest to install.