Published at Saturday, July 15th 2017. by Nanine in Flooring.
Traditional tile installation requires many tools and lots of patience which have to be pre-set on the floor, cut down to size, then adhered to the floor using a strong industrial glue. They will not stick to every surface and frequently, a layer of floor base must be installed before the tiling work can begin. If the tiles are placed too close together, they can buckle, leaving unsightly bumps and lumps on the floor. If they are placed too far apart, there will be obvious gaps. If a mistake is made when laying down the tile, it is very difficult to fix as the tile is glued to the floor. The tile will have to be pried up, excess adhesive scraped, and the process started over. Laying traditional tile floors is a project that can take several days, to several weeks, to finish.
There are three main types of sub-flooring installed to cover and span the floor structure. It is over this that the finished floor will be placed. The sub-flooring types include raw sheathing, interlocking and strip. It is utilized not only to provide a surface for the interior finishes to be placed on, but also to prevent twisting or torque forces placed on the building. The sub-floor also allows load sharing within the joist framing system. Often the sub-flooring is glued to the joist work to eliminate creaking floors and to prevent the floor joists from turning.
Ceramic tile is probably the most durable types of flooring and is typically installed in entry areas, where sand scuffing and water accumulations are the norm. Bathrooms and kitchens often get this type of floor treatment as well, but due to the high cost of installation, homeowners tend to not include these areas. Ceramic tile are typically a square tile, although interlocking units are on the market, in standard square measurements of 4", 6",8" or 12". They are installed by one of two primary methods, either set into a thin mortar bed (called "thinset adhesive"), which also acts like glue, or a heavyset bed of 1-1/2" normal mortar base. For all ceramic tile installations, the floor must be built up to ensure the strength required to prevent tile or joint cracking. Often, installers put down a material called "cement board", which is much like drywall, but is made of glass fibers and cement. In any case, ensure that your installer will offer you a guarantee against future cracking or uplift of tiles. Ceramic tiles require little maintenance, but beware, water on glossy floor tiles can be very slippery, and many a time, a homeowner has resented the installation of a high gloss tile, over a bathroom floor area.
However if you go for a quality engineered wood flooring you can even gone as far as to boil a piece of our floor for 30 minutes and the board still will not de-laminate. The 15mm ply wood under core is what gives the flooring the strength and stability is has. Oak is a natural product and when used for flooring the board widths can change in size. This can cause gaps between boards or the floor to buckle and this movement is most commonly caused by the changing of humidity in the environment. Because of the stability of a quality engineered oak floor it is far less prone to this movement. This stability is also becoming of greater importance today due to the fact that an increasing number of properties are having under floor heating systems installed, which of course causes a frequent change in humidity. Having said this I would again like to reiterate that I am writing in regards to a quality, higher spec engineered oak flooring, and I can not talk for all engineered wood floors.
You can choose furniture coasters from a vast array of styles at most any hardware, home improvement or house ware shop. Styles and techniques range from special materials that are circular, oval, and rectangular or square which peel and stick to smooth surfaces with special materials attached to metal frames which can be used in your wooden floor surface`s care by hammering them into the legs` bottoms of furniture. An alternative would be to make furniture coasters for your hardwood floors and wooden floors` care. Coasters can also be used to protect the tops of wood furniture against circles which form from glasses or cups containing liquids.
Are you going to be able to enforce the warranty? Also, do you really think that a finish can last a lifetime? For example take a nail and try scraping it across the surface. Sure it is a durable, well applied finish, but it is impossible to make a product that won`t get abused at some point in its lifetime. Do you think that the only serious trial your floor will ever see is a stinky sock? Read the fine print on the warranty and regardless of what it says consider the true replacement cost on the floor. It probably only covers the cost of material of the specific damaged product under normal wear and tear. Your product may not be made exactly the same later (trends and product lines change) to replace the section that is warrantied, so you may have to replace the whole floor years later. You will have labor cost along with displacement of trim, cabinets, and appliances. Also most of these lifetime finishes cannot be repaired or sanded because of a micro bevel put on the edge of prefinished floor. Our advice is instead to buy a quality product that can be refinished and repaired because something will go wrong in the lifetime of the floor; don`t get a false sense of security.