Orlene. Flooring. July 13th , 2017.
Are you going to be able to enforce the warranty? Also, do you really think that a finish can last a lifetime? For example take a nail and try scraping it across the surface. Sure it is a durable, well applied finish, but it is impossible to make a product that won`t get abused at some point in its lifetime. Do you think that the only serious trial your floor will ever see is a stinky sock? Read the fine print on the warranty and regardless of what it says consider the true replacement cost on the floor. It probably only covers the cost of material of the specific damaged product under normal wear and tear. Your product may not be made exactly the same later (trends and product lines change) to replace the section that is warrantied, so you may have to replace the whole floor years later. You will have labor cost along with displacement of trim, cabinets, and appliances. Also most of these lifetime finishes cannot be repaired or sanded because of a micro bevel put on the edge of prefinished floor. Our advice is instead to buy a quality product that can be refinished and repaired because something will go wrong in the lifetime of the floor; don`t get a false sense of security.
Strip floors, were once the most popular type of sub-floor installed. But with the introduction of manufactured sheathing products, it has become less utilized. Strip floors consist of 1" by 6" or 8" boards, placed diagonally over the floor joist framing system. It is slightly more expensive to install, and requires experienced tradesmen. To install such floors properly, the lumber should be non-kiln dried, with a relatively high moisture content. This may seem odd, but in reality, as the wood dries out, it will shrink.
So, a top quality oak engineered flooring will look the same but will it actually last as long?. How long a floor will last is mostly down to something called its `wear layer`. The part of the floor that is classed as the wear layer is from the surface of the board down to the tongue and on a solid oak board this would be around 5-6mm. Now, the wear layer on engineered wood flooring is the top layer of oak. So if you purchase an engineered oak flooring which has a 5-6mm solid oak top layer it will result in the flooring lasting just as long. In conclusion if you want an engineered flooring that is going to last as long as a traditional solid oak floor then make sure it has a nice thick top layer of wood, ideally 5mm+.
Laying the floor is also another area that is worth thinking about when comparing the two types of oak flooring. The majority of engineered wood floors are longer and wider than most solid oak boards because this is the look that most people are wanting nowadays. The flooring being longer and wider means the flooring is quicker to fit. Another aspect that makes this floor easier and quicker to fit is how well machined the boards are. From our experience in the flooring industry we have had nothing but good feedback regarding how easy our engineered flooring was to lay, and this is down to how well machined the boards are. Given that engineered flooring is quicker and easier to fit, any extra money that is spent on purchasing an engineered oak floor is often compensated in the time that is saved fitting it! This is something to keep in mind when comparing prices.
Fifth, compare overall thickness and the height from the top of the tongue or nail groove to the top of the face on the floor. On an engineered floor this is generally the thickness of a wear layer. Most solid wood floors are 3/4" overall before sanding (but some are less) with 1/4" above the nail groove. Our engineered floor is manufactured to equivalent measurements but most engineered floors have a thinner wear layer. This comes down to how many times the floor can be sanded. What kind of finish and texture you want on the floor factors into how deep you will re-sand the floor during refinishing. A number of our reclaimed wood floors are sold with an original texture that shows the old saw marks and character in the floor, so most likely you won`t want to sand this out. As a rule of thumb, the thicker the wear layer then the longer the floor will last.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does ArticleDirectorySeo claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.